Personal system of discountsfor wholesale buyers
Consultation technologistselection of the dispersion and the adhesive, the implementation in the production
Term of execution of the order from 3 daysround-the-clock production
Click on the picture to enlarge
UMACOLL 83M
Technical conditions: 2252-034-20514586-15
- Container:
- 30 kg (plastic bucket)
Description
One component water-based polyurethane-dispersed adhesive with technological additives for 3-D lamination.
Protect from freezing!
Usage
DESCRIPTION
One component water-based polyurethane-dispersed adhesive with technological additives for 3-D lamination.
Protect from freezing!
FIELDS OF APPLICATION
Umacoll 83M is used for wood-based textured boards (HDF, chipboards, laminated chipboards, MDF, etc) 3D-lamination and thermo veneer with thermoplastic films (PVC, PET, ABS) in membrane and vacuum presses.
SUBSTRATE
Easy to spray. Suitable viscosity application. Finished adhesive bond has a high initial strength, moisture and steam resistance, frost resistance up to-40°C and thermal resistance not less than +75°C.Technical information
|
|
Umacoll 83M |
|
Base |
Polyurethane dispersion |
|
Form |
Customer’s demand in two modifications - white, dry transparent; - blue, dry bluish-transparent |
|
Viscosity, Brookfield LVT, mPa*s |
1000-4000* (23/63/12) |
|
Density, g/cm3 |
1,040±0,02 |
|
рН value |
7,5±0,5 |
|
Reactivation time |
24 hours |
|
Activation temperature **, оС |
55-65 |
|
Bond thermal stability, оС |
not less 75 |
Application
INSTRUCTION FOR USE
Gluing materials surface should be dust-free, without fat and other contaminants.
CONDITIONS
Working temperature +15°С, optimum temperature (20±2)о С and air humidity no more than 65%. At lower temperatures pressing time and temperature should be increased.
Gluing materials and glue should be withstood to the room temperature before use.
WORKING CONDITIONS
|
Preparing |
Ready to use. Stir thoroughly before use and filter through the polymer mesh to delete films and flocculated polymer to prevent spraying nozzle loading. Umacoll 83M is ready to use as one-component glue. |
|
Pot life |
Umacoll 83M viability is not limited during the warranty period of storage. |
|
Cleaning |
Spray gun. Optimum nozzle diameter 1,2-2,0 mm, spraying pressure 2,4-4 bar. (Nozzle diameter and pressure data are obtained using DeviBiss PRI PRO 210-14k. Pressure is set at injection tube output). Nozzle diameter and optimum pressure should be defined in each case individually. Glue contact materials should be corrosive resistant. No contact with copper, aluminium and zinc (glue coagulation is possible). |
|
Application |
Equipment is washed with water before glue drying. Dry glue is cleaned mechanically. Tools has to be dry before refilling. |
|
Adhesive |
Spray gun on glued materials bearing side. Glue consumption is about 50 g/m2. Milled rounded 3D - surface areas (surfaces with high absorbency) should be retreated with glue second layer after first layer complete drying. Optimum technological parameters should be set regarding manufacturing conditions and materials used. Bonding layer must be dried at room temperature before pressing. First layer drying is 30 min., second layer drying is 60 min. To fasten drying time use heat increasing drying temperature up to 30-350C. Bonding is achieved by adhesive line thermo activation. Pressing conditions: - Pressing time: 30-90s - Press temperature: 80-1200C* - Pressing pressure: 4-5 bar Optimum technological parameters should be set regarding manufacturing conditions and materials used. Glued parts can be machined after 6 hours. Full time of hardening is 3-7 days. *Depends on the film and other pressing conditions. |
Storage
STORAGE
Should be kept in tightly closed original container in dry rooms, not below +5° up to +30°С. Protect from freezing!
GUARANTED STORAGE LIFE
Umacoll 83M expire date is 6 months in case if delivery and storing rules are followed. After expire date shouldn’t be used without tests.
HEALTH AND SAFETY
Careful air change is necessary. Use rubber gloves to protect hands. Avoid skin or eye contact. In case of contact with eyes or skin wash with water and consult a doctor. Keep away of children. During spraying required respiratory protection. For detaled safety instructions, please read safety certificate.
